• PW0-300题库demo免费下载

  Filed under CWNP
  Aug 3

  CWNP认证PW0-300考试题库介绍

  考试代号: PW0-300
  问题数量:140 Q&As
  
  更新时间: 2009-09-26
  注册地点: Prometric/Pearson VUE
  题库全称:Certified Wireless Network Expert

  免费PW0-300题库Demo赏析

  　
  　
  Exam : CENP PW0-300
  Title : Certified Wireless Network Expert

  1. When using a protocol analyzer to capture conversations over a WLAN, you may often encounter encrypted data frames. Most WLAN protocol analyzers have a feature that allows the analyst to save and reload the captured frames into memory at a later time. Using this functionality, what task can be performed?
  A. When IEEE 802.1X/LEAP is being used as the WLAN security mechanism, the authentication response frame can be replayed from a saved trace file at a later time to successfully authenticate a hacker.
  B. If a user name and password for an IEEE 802.1X/EAP-TTLS security implementation can be obtained through social engineering tactics, the user name and password can be entered into the analyzer to decrypt the frames from a saved trace file.
  C. An analyst can search through the captured frames looking for RADIUS frames that will disclose the user’s password.
  D. Encrypted frames may be decrypted offline, after they are captured, by entering a WEP key or WPA passphrase into the analyzer.
  Answer: D

  2. Many autonomous access points support IEEE 802.1Q VLAN tagging. When analyzing a WLAN system using IEEE 802.1Q tags, where can the VLAN tag number be seen?
  A. In the Sequence Control field of the MSDU
  B. In the PLCP header’s Service field
  C. In the Frame Control field of the MPDU header
  D. In the Ethernet header on the wired port of the access point
  E. In the Beacon Management frame’s Capabilities fixed field
  Answer: D

  3. Given: ABC Company has implemented a QoS capable IEEE 802.11 WLAN controller based network with lightweight access points as shown in the graphic.
  What is the advantage of the access point mapping IEEE 802.11 user priority (UP) values to DSCP values in the IP header that encapsulates the 802.11 frame?
  A. Direct mapping of UP-to-DSCP values increases effective throughput between the access point and WLAN controller.
  B. Since UP-to-802.1Q PCP mappings are not possible at the access point, the only method of prioritizing upstream data is through UP-to-DSCP mappings.
  C. The QoS markings will survive layer 2 hops that could remove 802.1Q PCP values.
  D. UP-to-DSCP mappings are more granular than UP-to-802.1Q PCP mappings.
  Answer: C

  4. What does a TXOP Limit value of 0 in the EDCA Parameter Set included in a QoS AP’s Beacons or Probe Response frames indicate?
  A. It indicates that one or more MSDUs or MMPDUs must be transmitted at the lowest basic rate during each TXOP.
  B. It indicates that QoS STAs must wait for the HC to transmit a Polled TXOP before they can transmit MSDUs or MMPDUs.
  C. It indicates that no MSDUs or MMPDUs may be transmitted by a non-pollable QoS STA.
  D. It indicates that a single MSDU or MMPDU may be transmitted at any rate for each TXOP.
  E. It indicates that QoS STAs may transmit voice MPDUs (Access Category 7, during TXOPs.
  Answer: D

  5. What is indicated to a QoS AP when a QoS STA sets U-APSD Flag bits to 1 in Association and Reassociation frames?
  A. Which access categories are both trigger- and delivery-enabled.
  B. The maximum number of data frames that should be queued by the QoS AP for that QoS STA.
  C. The number of TXOPs that are requested by this QoS STA.
  D. Which user priorities are mapped to access categories.
  E. Which access categories are scheduled.
  Answer: A

  6. According to the IEEE 802.11 standard (as amended), transmit power information is carried in which frames?
  A. TPC Report frame
  B. ADDTS Response frame
  C. Probe Response frame
  D. Beacon frame
  E. Channel Switch Announcement frame
  F. Measurement Report frame
  Answer: ACD

  7. In an ERP QoS BSS using APSD, when is the Power Management subfield of the Frame Control field set to a value of 1?
  A. Only in management frames sent by a non-AP QoS STA immediately prior to entering a low power state (dozing).
  B. On any QoS Data frame sent by the QoS AP subsequent to a PS-Poll frame.
  C. On any frame transmitted by a non-AP QoS STA using APSD.
  D. Only in the PS-Poll frame sent from a STA operating in PS mode.
  Answer: C

  8. The IEEE 802.11 (as amended) Dynamic Frequency Selection (DFS) service is capable of performing what functions?
  A. Establishing a interference baseline on all 2.4 GHz channels
  B. Using modulation switching techniques to avoid interfering with radar systems
  C. Testing channels for radar before using a channel and while operating in a channel
  D. Suspending operations on a channel with high IEEE 802.11 co-channel interference
  E. Requesting and reporting of measurements in the current and other channels
  Answer: CE

  9. Given the IEEE 802.11 Beacon frame decode shown, determine which statement is true.
  A. The access point is operating on channel 3.
  B. The access point has both 1 Mbps and 2 Mbps configured as basic rates.
  C. This Beacon frame came from an ERP access point.
  D. The duration value of 0 ec means that this access point is operating in HEMM mode.
  E. ERP mobile stations must use the RTS/CTS protocol before Data transmissions.
  Answer: C

  10. Which statement is FALSE regarding use of admission control in a QoS BSS?
  A. The IEEE 802.11 QoS facility implements a single admission control mechanism for use in contention-free periods (CFPs) and contention periods (CPs).
  B. The ACM bit is static for the duration of the lifetime of a BSS.
  C. If a QoS STA desires to send data without admission control using an access category (AC) that mandates admission control, the QoS STA will use a lower priority AC that does not use admission control.
  D. A QoS AP uses ACM subfields in the EDCA Parameter Set element to indicate admission control requirements for each access category (AC).
  E. A hybrid coordinator may enforce admission control policies during both contention-free periods (CFPs) and contention periods (CPs).
  Answer: A

  11. ABC Corp has just installed a single HR-DSSS access point into their medium-sized office environment. As the WLAN administrator at ABC Corp, you use a wireless protocol analyzer to troubleshoot a performance problem. You place your analyzer close to the access point, and capture some traffic from office users.
  Given the screenshot shown, which statement offers the best explanation for the poor WLAN performance of ABC’s new HR-DSSS WLAN?
  A. There is likely a source of RF interference somewhere around the access point. This is causing many data frames to be retransmitted, so overall WLAN throughput has been greatly diminished.
  B. Due to an ERP client joining the BSS, protection mechanisms have been enabled in the BSS by the access point. These protection mechanisms greatly increase protocol overhead, thereby decreasing overall WLAN throughput.
  C. A nearby HR-DSSS access point is operating on an adjacent channel causing a significant amount of corrupt frames within ABC’s BSS. These corrupt frame fragments are congesting the channel on which ABC’s WLAN is operating, thereby decreasing its throughput.
  D. One of the WLAN users has moved far enough away from the access point that his client station has begun transmitting frames at the minimum supported data rate. Even when a single user uses this rate for Data frames, throughput for the entire WLAN as a whole is slowed significantly.
  Answer: D

  12. The IEEE 802.11 standard allows for frame fragmentation. Which two fields in the IEEE 802.11 frame are involved in numbering data frame fragments and notifying the receiving station when all of the fragments of a data frame have been received?
  A. Capability Information field
  B. Frame Control field
  C. ERP Information field
  D. Sequence Control field
  E. DS Parameter field
  F. Ordered Service field
  Answer: BD

  13. Given: An ingress frame arrives on the Ethernet port of an autonomous AP marked with an IEEE 801D user priority value.
  Which IEEE 802.1D user priority values (by name) will assure the data payload carried by the Ethernet frame gets assigned to the highest priority WMM queue?
  A. Controlled Load
  B. Network Control
  C. Video
  D. Voice
  E. Best Effort
  F. Excellent Effort
  Answer: BD

  14. In a Split MAC wireless network architecture, lightweight APs map user priorities (UPs) specified by the QoS STA on incoming frames to ___________.
  A. IEEE 802.1D Frame Precedence Values
  B. GRE Priority Bits
  C. IEEE 802.1Q Tag Protocol Identifiers
  D. IP Differentiated Services Code Points
  E. QoS Control Header Values
  Answer: D

  15. Given: ABC Company is implementing a QoS enabled infrastructure that will support both voice and data. The WLAN controller is connected to one of three core layer-3 Ethernet switches. Each core layer-3 Ethernet switch has multiple edge layer-2 Ethernet switches attached. Lightweight APs are connected to all edge layer-2 Ethernet switches. The WLAN controller is on subnet 10.1.1.0/24, and the APs are on numerous other subnets. The APs are connected to the WLAN controller via LWAPP tunnels.
  When IEEE 802.11 frames arrive at a lightweight AP from a QoS STA that need to be sent to the WLAN controller, which bits can the AP mark to signal the layer-2 and layer-3 Ethernet switches to use higher priority processing?
  A. The Ethernet frame’s 802.1Q priority tag bits
  B. The IP header’s TOS bits
  C. The IEEE 802.11 frame’s QoS Control bits
  D. The LWAPP header’s C bit
  E. The UDP header’s PRI bits
  Answer: AB

  16. Given: When the delayed Block Ack policy is used between two QoS STAs, the recipient must respond to a BlockAckReq frame with an ACK frame. The recipient must then send its BlockAck response frame in a subsequently obtained TXOP.
  Once the contents of the BlockAck frame have been prepared, the recipient must _______________.
  A. Send the BlockAck response frame to the originator in the earliest possible TXOP using the highest priority AC.
  B. Send an ATIM to the originator signifying that the BlockAck response frame is ready for transmission.
  C. Include the TID of the BlockAckReq in the next TXOP Request to the HC.
  D. Wait for one PIFS after the next Beacon and transmit the BlockAck response to the originator using the same AC as the BlockAckReq frame.
  Answer: A

  17. How long, in microseconds, is the required Slot Time announced by an AP in an ERP BSS when both HR-DSSS and ERP-OFDM client stations are associated to the AP?
  A. 2
  B. 4
  C. 9
  D. 10
  E. 20
  Answer: E

  18. Which statements accurately describe IEEE 802.11 EDCA collision handling in a WMM compliant infrastructure WLAN?
  A. Data frames from lower priority colliding ACs behave as if there were an external collision on the wireless medium.
  B. Collisions between contending EDCAFs within a QoS STA are resolved within the QoS STA
  C. WMM-compliant applications collaborate within a QoS STA to handle transmission collisions at layer 7 of the OSI model
  D. The WMM specification requires use of RTS/CTS as part of the EDCAF in each QoS STA to avoid internal collisions between applications
  E. Collisions within a QoS STA do not require setting retry bits in MAC headers of MPDUs from lower priority ACs
  Answer: ABE

  19. A QoS STA obtains a TXOP for an access category (AC) after what two parameters are met?
  A. After a scheduled service period ends
  B. The medium is idle at the AIFS[AC] slot boundary
  C. The backoff time for that AC has expired
  D. After a Block ACK Response
  E. After a Target Beacon Transmission Time (TBTT)
  Answer: BC

  20. What events will cause an established TSPEC to be deleted by a AP?
  A. Disassociation of the non-AP QoS STA using the TSPEC from the QoS BSS
  B. Traffic Stream inactivity timeout
  C. Reassociation of the non-AP QoS STA with another QoS AP
  D. Receipt of a DELBA frame from a non-AP QoS STA
  E. Receipt of an Update TSPEC frame from a non-AP QoS STA
  F. A Controlled Access Phase (CAP) burst
  Answer: ABC

  免费下载PW0-300题库Demo

  Examsoon提供最新的CWNP认证 PW0-300题库，其全名为：(Certified Wireless Network Expert). 在您决定是否购买之前 可以先下载PW0-300题库的部分演示. Examsoon是全球唯一提供所有IT认证考试题库demo免费下载的厂商 ，以下为免费PW0-300模拟测试题的下载链接

  免费的PW0-300题库PDF下载链接

  CWNP PW0-300学习指南

  CWNP认证 PW0-300考试已经证明了它在全世界的广泛性和重要性，因此明白这项认证考试的世界各地的人必须具备与认证考试相关领域所需的技能和知识。CWNP认证 PW0-300学习指南的目的是检查考生的能力和他对概念的意识。很多时候练习测试PW0-300考试都已经被修改过了，删掉了许多过时的东西，而那些需求是在考试课程。当应用到时候你所学的知识的时候，就会鉴定出你所学到的东西以及对所学知识的应用是多么的恰到好处。CWNP认证 PW0-300是在IT行业的知名品牌，所以如果您通过了这样一个知名公司举行的一次考试，你可以想象你将来的事业会做的多么好。

  想要通过这个考试当然存在很多困难。你所要做的就是准备好充足的勇气和信心，而这些都来源与你平时训练的好坏.建议大家可以去Examsoon这个网站看一下，它的PW0-300考试是为了测试您在这方面的知识的掌握程度，最好的部分是它可以使你不断更新你所学的知识，不断进步。如果你知道所有的概念和如何使用他们的时候才是你真正掌握了Examsoon的用意。这门考试检查了您的能力和一旦你通过这次考验你将成为最优秀的人才，其他PW0-300考试的Examsoon结算值得注意的影响就是你的薪水将直线上升这大概也是每个人都希望获得的，所以要找一些好的资源才行。

  Examsoon考题大师PW0-300试题都是考试原题的完美组合，覆盖率95％以上，答案由多位专业资深讲师原版破解得出，正确率100％，只要您使用Examsoon的考试题库参加PW0-300考试，保证您一次轻松通过考试；

  售后服务第一！我们相信要想在当今时代取得成功，必须为广大用户提供全套的周到细致的全程优质售后服务，只有客户满意了，才能发展。客户至上是Examsoon考题大师的一贯宗旨；
  
  

  No Comments

Leave a Reply

You must be logged in to post a comment.